Brick treads framed with landscape painting timbers make attractive steps between dissimilar levels in your yard , and with our DIY templet , you’re able to install them yourself .
What You’ll Need
Equipment / Tools
Materials
Instructions
How to Build Timber and Brick Paver Steps
Timbers come in various sizes , and the sizing of the forest you use will affect both the dimensions of the steps and the possibility for brick patterns within the skeletal system . see out what ’s uncommitted and habituate the factual measurements to draw a dimensioned architectural plan . Most timber come in 8 - foot lengths , everlasting for steps 4 feet spacious .
When you project your brick paver steps ( and before you initiate cut into ) , decide on abrick pattern . employ a pattern write of whole bricks so you could head off cutting them . Choose the brick , purchase the right quantity , and dry - lay it on a monotonous surface in the normal of your alternative . Then , use the dimensions of this mocked - up division to cut the timbers to fit .
The plan shown here uses rebar to anchor the timbers into the soil . If your soil is flaxen , use a 2 - infantry length of 3/4 - in pipe or steel conduit instead .
Carve Risers
Make the steps with a riser main height equal to the forest meridian and a easy tread length . Lay out the site with stakes and mason ’s cable . Then , delve rough recessesin the pitcher’s mound , with the first recess 6 inch longer ( front to back ) than the factual tread .
Lay Out Brick Paver Steps Formation
repose out the brick stride on a flat airfoil and measure the dimensions of the layout . Cut lumber to these measurements and test - fit them around the brick . straightforward the recession with a framing square .
Assemble Timbers
To put together the timber , drill original holes for 12 - inch spikes entirely through the front face of the outside timbers and about 2 inches into the side timber . aim the spikes with a small-scale sledgehammer . At the corners of the rear tone , center a mark on the top face , about 4 inches from the end . Mark the middle of the timber also . bore a 1/2 - inch hole through the timbre . ( You ’ll motor rebar anchors through these holes when you set the skeleton . )
Set First Frame
Set the frame for the bottom brick paver step in the lowest recess in the ground . Lay a4 - foot levelacross the sides of the frame and level it . pitch the frame from back to front at the rate of 1/4 in per foot . To get the slope mighty , lay a 2 - foot grade on the side timberland with a 1/2 - inch spacer under one end . The gradient is correct when the bubble is centered .
Set in Place
When the first frame is right leveled and splash , cut 24 - inch distance of 1/2 - inch rebar and drive them through the holes in the rear timbers and into the soil .
Lay Second Frame
Lay the second frame on the first . The front lumber of the top skeletal frame lies on the rear timber of the humiliated one , with their faces affluent . Drill three pilot holes through the top timberand partway into the bottom one . Then , drive12 - in spikesinto the holes . incline the second form and anchor the rear timberland with rebar driven into the holes you drilled in Step 3 .
Continue Installation
add the remaining frames , fasten and sloping them and anchoring the rearward timbers with rebar . Make sureeach skeleton is levelfrom side to side before installing the next one .
Fill Gravel and Sand
Excavate the break until it ’s deep enough for a3 - in layer of crushed rock , 2 inches of sand , and your pavers ' thickness . pack down the stain in each break with the ending of a 2x4 , then laylandscape fabricon the grime . Shovel in the gravel , rase it , and tamp down it . Add the Amandine Aurore Lucie Dupin and tamp down it as well .
Level Sand
Make a recessed screed by nailing a 1x4 to a 2x4 . The bottom bound of the 1x4 extends below the frame by the thickness of a paver . Screed the sand degree and smooth .
Set Pavers
Set the pavers in the frame in the pattern for the brick paver tone you used to determine the frame attribute . Bed them in the sand with a rubber mallet , and charge them as you would the surface of abrick - in - moxie patio .
Fill Joints
Shovel a thin layer of builder ’s sand onto the brick and use a brush to span the sand into the joints . cloud the joints and light touch on more backbone , repeating the operation until the joints are filled .
How to Build Timber-and-Brick Entry Steps
Timber - and - brick paver steps are easier to install than poured concrete and give an cozy feeling . However , the 5 - 1/2 - column inch riser peak may not be desirable in all instances . Lay out the steps , set up the timbers , and set the brick for yourentryway stepsas you would for footfall in the landscape .
Build Timber and Install Gravel
Build and anchor timber forms with right rise , run , and interior dimensions to accommodate your brick pattern . Excavate the recess ( if necessary ) to hold4 to 6 inchesof crushed rock , 2 inches of guts , and the paver thickness . set up the gravel and Baroness Dudevant , then screed the grit in the time out .
Lay Pavers
pop with the bottom gradation , lie the pavers , bed them with a rubber hammer and level them . pass around fine Baroness Dudevant on the Earth’s surface and sweep it into the joint . Mist the sand with water , tote up more sand , and reiterate the process until the joint are fill .
Outdoor DIY Projects for a Beautiful Yard
